Search Results

Using the CDC (SAE J224), a comparison of the NASS data and the UMTRI field accident files (UM series) indicates a similar distribution of offset frontal crashes. Offset frontal damage occurs in 56-61% of crashes, often involving more than one third of the front of the car. Lap-shoulder belted drivers sustain more AIS 2 or greater injuries when there is interior intrusion and occur more often when the offset damage is in front of the driver. However, this may well be due to the severity of the crash. European studies have no uniformity as to offset frontal collision descriptors are difficult to interpret, or to compare one to another.

Cost reduction, quality improvement, and regulatory compliance are well-recognized competitive issues. Companies must excel along each of these fronts while operating in an environment of rapid and multi-faceted change, limited financial and human capital, and increasing product development time pressure. In addition, consumers are demanding automobiles that provide greater performance, function, and comfort while emitting lower emissions, consuming fewer gallons of gasoline, injuring fewer humans, and requiring fewer dollars to build and purchase. A solution to these seemingly conflicting objectives is to take a systems view of the product and industry. This paper explores the material decision process so that manufacturers, component suppliers, and material providers may better understand the interlocking web of compromises that shape the pursuit of value-added alternatives and avoidance of unprofitable compromises.

The automobile industry has been using high-density polyethylene (HDPE) as a material to fabricate fuel tanks. Because untreated HDPE is permeable to the primary constituents of gasoline, these fuel tanks are now being produced with various barrier technologies that significantly reduce this permeation rate. Four currently available barrier technologies are fluorination, sulfonation, coextrusion, and the laminar barrier technology. These technologies have successfully proven to decrease the permeation rate of pure gasoline. However, it is suspected that their effectiveness may be reduced when alcohols are introduced into the fuel blend. In this work, we determine the permeation rates of gasoline-alcohol fuel blends through HDPE by conducting tests on 22-gallon HDPE fuel tanks and on small HDPE bottles fabricated with and without these barrier technologies. The goal of this study is to provide a comprehensive evaluation of these four barrier technologies.

NASS 80-88 passenger side impacts data were analyzed. Location of primary car damage using the CDC classification, the AIS for injury severity studies, and the interior contacts of the various body areas. Drivers alone, or with passengers were studied separately in both left and right side crashes. Direct impacts to the passenger compartment only are less frequent than to other CDC side zones. Driver interior contacts vary by body region but also by side impacted in the crash. The presence of an unrestrained front passenger appears to enhance driver injury level in left side crashes but the presence of a passenger, in right side crashes appears to moderate driver injury severity.

Originally written in 1976 and previously revised in 1983, The Maintenance Council (TMC) Recommended Practice RP-404B is intended to enhance the safety of motor carrier employees by providing guidance regarding the purchase and use of access systems on heavy truck and truck tractors. Compliance with the recommended practice is intended to permit anyone entering or exiting a cab to have three limbs in contact with the truck or truck-tractor at arty time. The scope of the recommended practice covers access systems to the cab and rear of cab areas of all types of heavy trucks and truck tractors, in contrast to Bureau of Motor Carrier Safety (BMCS) regulations which applies only to Cab Over Engine (COE) tractors. The Maintenance Council recommended practice also varies from the BMCS requirements in that it remains a design oriented document.

Intelligent Vehicle-Highway Systems (IVHS) improve the operation of cars and trucks on public roads by combining information technology with road transportation technologies. The basic ideas about IVHS are by no means new but a number of converging forces have encouraged significant IVHS development in North America recently. Based on the results of a Delphi survey to project realistic future scenarios, both applied and fundamental research agenda are being formulated in a Michigan-based IVHS program to push the IVHS technologies for advanced motorist information systems and for backup vehicle controls under emergency conditions. The scope of the research agenda includes social/human elements as well as hardware and software technological systems. The Michigan research program is expected to contribute to the development of IVHS in North America, both technically and institutionally.

Designing trucks for good ride characteristics is a challenge to the engineer, given the many design constraints imposed by requirements for transport productivity and efficiency. The objective of this lecture is to explain why trucks ride as they do, and the basic mechanisms involved. The response of primary interest is the vibration to which the driver is exposed in the cab. Whole-body vibration tolerance curves give an indication of how those vibrations are perceived at the seat; however, ride studies have shown that visual and hand/foot vibrations are also important to the perception of ride in trucks. The ride environment of the truck driver is the product of the applied excitation and the response properties of the truck. The major excitation sources are road roughness, the rotating tire/wheel assemblies, the driveline, and the engine.

Rolling resistance measurements were made on a sample of twenty-four retreaded and four new truck tires spanning a variety of constructions, tread patterns and tread depths. Examination of the results showed some relationship between three construction features and the resulting rolling resistance values. These are (a) Radial or bias carcass construction, (b) Tread pattern, and (c) Tread depth. The latter two characteristics can over-ride radial or bias construction effects. The effect of tread compound could not be analyzed in this limited test program. Good quality retreaded truck tires can exhibit comparable rolling resistance with new truck tires.

Secondary injection in a diesel engine is defined as the introduction of additional fuel into the combustion chamber after the end of the main injection. It is usually caused by residual pressure waves in the high-pressure pipe line connecting the pump and injector. When these waves exceed the injector opening pressure, secondary injection occurs. Tests revealed that the U.S. Army TACOM single-cylinder engine used in this investigation, fitted with an American Bosch injection system, had secondary injection within the normal engine operating region. The pump spill ports and delivery valve were redesigned to eliminate secondary injection, in accordance with previously reported work. Comparative tests of both the conventional and modified injection systems were run on the same engine, and the effects of secondary injection on engine power, economy, and exhaust emissions were determined.

Lap-shoulder belt effectiveness has been indicated by many authors, however there is minimal information on the more severe injuries to lap-shoulder belted car occupants. This paper presents details of 15 lap-shoulder belted occupants in frontal collisions and 24 lap-shoulder belted occupants in side impact collisions. Case descriptions of these crashes are presented, each including vehicle, environmental and injury details.

After-injection is the introduction of additional fuel to the combustion chamber after the end of the main injection. It is a persistent diesel fuel injection problem which usually results in reduced engine power and economy and increased emissions. After-injection is caused by uncontrolled pressure transients at the injector after the opening of the pump spill port. These pressure transients are related to the wave propagation phenomena in the high-pressure pipeline connecting the pump and injector. Use of experimental trial-and-error methods in attempts to control this phenomenon has met with limited success. The analytical control method described in another paper is used to determine design means by which after-injection may be controlled. Further investigation and evaluation of two design changes which release the injection system excess elastic energy in a controlled manner are considered herein. One design change is the addition of a control valve in the pump delivery chamber.

A theoretical digital simulation of a conventional diesel fuel injection system has been developed. The influence of such factors as wave propagation phenomena, pipe friction, and cavitation are included. The computer results are compared with transient pressures as measured on an actual fuel injection system operated on a test bench. The comparisons show the accuracy and validity of this simulation scheme. Special attention is given to some of the important factors that affect the accuracy of the simulation model. These include the effect of pressure on the fuel bulk modulus and wave speed, the pipe line residual pressure, and the coefficient of discharge of important orifices.

Possible mechanisms for smoke formation in the diesel engine are discussed. Emphasis is placed on the effects of some engine and fuel factors on carbon formation during the course of combustion, including cetane number, fuel volatility, air charge temperature, and after-injection. The tests were made with a single-cylinder, open chamber research engine, with three fuels, covering a wide range of inlet air temperatures and pressures. There is evidence that smoke intensity increased with increase in the cetaine number of the fuels with inlet air temperatures near atmospheric. Increase in the air charge temperature caused an increase in smoke intensity for volatile fuels and had an opposite effect on less volatile fuels for the open chamber engine used. The smoke intensity was found to increase dramatically with after-injection, with all other parameters kept constant. The concept that flame cooling is the main cause for smoke formation is examined.

APPLICATION of nuclear energy for civilian automotive uses has possibilities, these authors say. Nuclear power for automotive applications, they feel, is technically feasible now where size and weight are not prime considerations; where size and weight are major parameters, discoveries of new materials for construction of nuclear-power reactors must be made. New materials are needed for reactor fuels, heat extractants, neutron reflectors, reactor construction materials, controls, and radiation shields which must have unique nuclear properties in addition to conventional engineering properties. This paper presents nuclear automotive propulsion devices in terms of technologies now available. The necessary radiation-shielding mass and weight requirements are presented for an ideal point-source nuclear-heat-power engine.